WELDING SKILLS FOR WORK IN EUROPE · WELD-05

All-Around, Field/Site & Supplementary Information

WELD-05 · Foundation · approximately 30 minutes with practice

One small symbol. A different job.

Two instructions may identify the same weld type and size while requiring different work. One may extend around a particular joint; another may be assigned to site installation. Additional indications can affect the required finished result.

Read these requirements with the complete designation, drawing views and supporting documents.

Extent → location → additional requirements
Three separate questions. This concept panel is not a complete production instruction.
  • How far does the specified weld extend?
  • Where must it be made?
  • What additional requirements apply?

Situation from work

A fabricated assembly contains a post-to-base connection and a separate installation connection.

The first detail identifies a weld around the post-to-base joint. The second is assigned to site welding. A note also refers to a finished-surface requirement.

A welder recognises the weld type but treats all connections as ordinary workshop work.

The problem is not the elementary symbol. The additional instructions have been missed.

Who is this for?

Welders, fitters, fabricators, installation personnel, candidates and team leaders who read drawings or prepare work.

You will gain a way to separate weld extent, execution location and finished-result requirements, and to raise useful questions before an operation becomes difficult to reverse.

Learning objectives and prerequisites

After this lesson, you should be able to:

  1. Explain why all-around does not mean every edge of a component.
  2. Distinguish site assignment from weld type and welding position.
  3. Separate contour from finishing method and acceptance requirements.
  4. Locate supplementary information and document references.
  5. Review a combined workshop/site scenario.
  6. Communicate unresolved scope or execution questions.

Review WELD-01–04 for document review, side location, weld type and dimensions.

Technical foundation

1. All-around concerns the identified joint path

A small circle at the junction of the arrow and reference line is the familiar all-around indication.

Interpret the path through the joint geometry and relevant views. It is not an instruction to weld every visible edge, every connection or both sides of every component.

For a simple hollow-section-to-plate example, the relevant path can be the perimeter where the section meets the plate. The plate’s outside edges are different locations.

Do not interpret all-around as a welding travel direction or a demand to complete everything in one uninterrupted run.

2. Field/site concerns execution location

A flag at the arrow/reference-line junction is the familiar field/site indication.

It identifies work to be performed outside workshop fabrication, usually at the installation location.

It does not define a welding process, qualification scope or welding position. Site welding is not automatically outdoor welding.

Read the project’s assembly and execution instructions. Do not transfer the weld into the workshop simply because access is easier there.

Conversely, absence of a local flag should not be used alone to resolve every execution-location question: check the complete project documentation.

3. Contour is not the same as finishing method

An indicated contour describes a required profile. It does not automatically specify which tool or process must achieve it.

Read any separate finishing, surface and dimensional requirements.

For example, a specified flush result does not give unrestricted permission to remove material. Confirm the required final geometry, permitted work and inspection requirements.

Do not invent finishing-letter meanings from a different standard.

4. Supplementary symbols and complementary information differ

A supplementary symbol is graphical information associated with the designation.

Complementary information can be written text, a reference or another non-symbolic instruction, including information in a tail.

Do not assume every requirement is a symbol, or that every note belongs in the tail. General notes, local details and referenced instructions may also apply.

5. Additional indications work together

An extent indication does not cancel size requirements.
A site indication does not replace the WPS.
A finished-profile requirement does not establish every acceptance criterion.

Review the complete combination. Where instructions appear incompatible, identify the conflict and request clarification.

Primary context: ISO 2553 and the applicable European/project adoption. Do not import AWS-specific finishing conventions automatically.

All-around concerns the identified joint
Conceptual example, without dimensions or technical symbol artwork.
  • Post-to-base contact perimeter: a possible indicated joint path.
  • Free plate edges: separate locations, not automatically included.
  • Confirm the exact extent in the views and project documents.

Technical terminology

ENPLWorking meaning
All-around indicationOznaczenie spoiny dookołaExtent around the relevant joint path.
Field/site weldSpoina montażowaWelding assigned outside workshop fabrication, usually at installation.
Weld extentZakres spoinyThe specified path or limits.
ContourKontur / profil spoinyRequired profile.
Finishing methodSposób wykończeniaSpecified method of obtaining the result.
Supplementary symbolSymbol dodatkowyGraphical additional information.
Complementary informationInformacja uzupełniającaWritten information or references.
TailOgon oznaczeniaA location for complementary information.

Review step by step

  1. Confirm drawing, revision, units and system.
  2. Locate the joint and designated side.
  3. Read weld type and dimensions.
  4. Identify the extent and trace its path through the views.
  5. Establish workshop/site assignment.
  6. Read contour, finishing and referenced requirements.
  7. Confirm the applicable WPS and execution instructions.
  8. Raise unresolved questions before the affected work.

This is a practical learning workflow, not a prescribed ISO sequence.

Worked example — VL-A501

Training package:

  • Joint J1: post-to-base perimeter weld.
  • Joint J2: installation connection assigned to site.
  • J2 also references finishing note F2.
  • F2 is unavailable.

Interpretation:
J1 does not authorise welding the base plate’s free edges.
J2 must not be reassigned to the workshop by preference.
The finishing requirement cannot be invented while F2 remains unavailable.

Clarification:
“For VL-A501, J2 is assigned to site and refers to F2. Please provide F2 and confirm the execution sequence before the affected preparation or finishing.”

This example supplies no weld size, process settings or acceptance limits.

VL-A501 — information in the package
Training example; the unavailable note needs clarification.
  • J1: identified post-to-base joint perimeter.
  • J2: connection assigned to site.
  • F2: referenced finishing note is unavailable.

Common mistakes

  • Reading all-around as every edge.
  • Treating all-around as one continuous production run.
  • Treating site assignment as a welding-position code.
  • Assuming site always means outdoors.
  • Moving work between workshop and site without authorisation.
  • Treating a profile requirement as an unrestricted grinding instruction.
  • Importing finishing abbreviations from another standard.
  • Missing referenced notes.

Try it yourself

A training detail identifies an all-around weld at a tube-to-plate connection. A separate connection is assigned to site and references note N7, which is missing.

A colleague proposes welding every plate edge, completing the site connection in the workshop and deciding the finish later.

Identify three problems and write one clarification question.

Show suggested answer

The all-around scope is tied to the indicated connection, not every plate edge.
The execution location cannot be changed by preference.
The missing note must be obtained before the operation it affects.

Question:
“Please confirm the joint path, retain or formally clarify the site assignment, and provide N7 before the affected work.”

Knowledge check

1. Does all-around mean every visible component edge?

Show answer

No. Identify the relevant joint path.

2. Does all-around automatically require one uninterrupted welding run?

Show answer

No. Extent and execution sequence are different questions.

3. Does a site flag establish the welding position or qualification scope?

Show answer

No. Check those separately.

4. Does a contour requirement automatically specify grinding?

Show answer

No. Read the method and other requirements.

5. Does a missing referenced note allow the welder to choose a substitute?

Show answer

No. Obtain or clarify the instruction.

6. Can an all-around extent and site assignment apply together?

Show answer

Yes, where the complete instruction specifies that combination. Read both. This is a learning check, not a qualification test.

Use it in a technical interview

Explain how you identify scope, execution location and additional notes.

Give an actual example of reading a connection and resolving a missing requirement. Keep experience separate from qualification coverage.

Use it with your team

Using an approved training drawing, have three people independently identify:

  • The joint path.
  • The execution location.
  • Additional requirements.

Compare their answers before discussing the sequence. Resolve differences through the workplace process.

Key takeaways

Extent, location and additional requirements are separate.
Read all-around through joint geometry.
Site assignment does not define process or position.
Contour and finishing method are different.
Do not invent missing instructions.

Practical bonus

Download the EN/PL workshop checklist — 2 pages

Accessible checklist:

  • Drawing — correct drawing, revision, units and symbol system?
  • Joint — which exact joint does the arrow identify?
  • Type and side — have I read the weld type and designated side correctly?
  • Dimensions — size, length, count and spacing interpreted correctly?
  • Extent — which joint path is covered by the all-around indication?
  • Location — workshop or field/site? Is the execution location confirmed?
  • Finish — contour, finishing and surface requirements understood?
  • Documents — applicable WPS and other required instructions available?
  • Clarification — have unresolved questions been raised before affected work?

Drawing / revision; joint / detail; question and person to clarify with. Use with complete project documentation and workplace procedures. This card does not authorise design changes or replace a WPS.

Previous / next

← WELD-04 — Weld Size, Length & Pitch

Next: WELD-06 — Welding Positions: What the Codes Mean

Candidates

Describe drawing interpretation and workshop/site experience alongside processes, materials, positions, preparation and qualifications.

Welding opportunities and Technical Talent Pool:
technicals@via-labora.com
WhatsApp +48 504 016 136

No specific vacancy is asserted here.

technicals@via-labora.com · WhatsApp +48 504 016 136

Employers

Discuss candidate preselection against the actual process, material, position, thickness/diameter, drawing, WPS, certificate and fabrication requirements.

marcin.ciupka@via-labora.com

Discuss recruitment cooperation

References

ISO 2553 publication:
Reference

TWI educational overview:
Reference

Editorial check: 9 November 2026.
Use the applicable project edition. The TWI overview contains historical references; it supports learning and does not replace the governing standard.